Ktestは我々が研究したトレーニング資料を無料に更新します。それは勉強者がいつでも最新の300-115模擬問題集をもらえるということです。Implementing Cisco IP Switched Networks模擬問題集の目標が変更されば、Ktestが提供した勉強資料も変化に追従して内容を変えます。
CiscoCCNP認定資格300-115試験問題集の目標はご成功の認定生涯のために最高のテスト問題ダウンロードと演習問題を提供するのです。受験者に最も全面的な問題集を提供します。当面の市場で勉強者に初めて困難を乗り越える信心を差し上げられるユニークなソフトです。CiscoCCNP認定資格300-115試験問題集は世界でどの国でも承認されて、すべての国が分け隔てをしないの試験です。
その他の認定は適切に300-115試験参考書などのような1つの機能をマークしていないし、他のターンアウトはハードワーク、努力、コミットメントと関与の時間と判明の質の面で300-115試験参考書に比較しません。Share some CCNP 300-115 exam questions and answers below.
Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a switch?
A. VLANs 1-1001
B. VLANs 1-4094
C. VLANs 2-1001
D. VLANs 2-4094
Answer: C
When SDM templates are configured, which action must be performed for the configuration to take effect?
A: reload
B: shutdown
C: write memory
D: backup config
Answer: A
Which statement about the MAC address sticky entries in the switch when the copy run start command is entered is true?
A: A sticky MAC address is retained when the switch reboots.
B: A sticky MAC address can be a unicast or multicast address.
C: A sticky MAC address is lost when the switch reboots.
D: A sticky MAC address ages out of the MAC address table after 600 seconds.
Answer: A
Enablement of which feature puts the port into err-disabled state when the port has PortFast enabled and it receives BPDUs?
A: BPDU filtering
B: BackboneFast
C: EtherChannel
D: BPDU guard
Answer: D
Interfaces are assigned to a VLAN, and then the VLAN is deleted. Which state are these interfaces in after the VLAN is deleted?
A: They remain up, but they are reassigned to the default VLAN.
B: They go down until they are reassigned to a VLAN.
C: They go down, but they are reassigned to the default VLAN.
D: They remain up, but they are reassigned to the native VLAN.
Answer: B
Which feature is automatically configured when an administrator enables a voice VLAN?
A: 802.1Q trunking
B: PortFast
C: QoS
D: private VLANs
Answer: B
Which statement describes?one major issue that VTP can cause in an enterprise network when a new switch is introduced in the network in VTP mode server?
A: It can cause network access ports to go into err-disabled state.
B: It can cause a network-wide VLAN configuration change if the revision number on the new switch is higher.
C: It can cause a network-wide VLAN configuration change if the revision number on the new switch is lower.
D: It can cause routing loops.
Answer: B
A network administrator configures 10 extended VLANs ranging from VLANs 3051 to 3060 in an enterprise network. Which version of VTP supports these extended VLANs?
A: version 1
B: version 2
C: version 3
D: VTP does not recognize extended VLANs.
Answer: C
An engineer is configuring an EtherChannel between two switches using LACP. If the EtherChannel mode on switch 1 is configured to active, which two modes on switch 2?establish an operational EtherChannel? (Choose two.)
A: active
B: auto
C: desirable
D: on E: passive
Answer: A, E
When a Layer 2 EtherChannel is configured, which statement about placement of the IP address is true?
A: The IP address is placed on the highest numbered member port.
B: The IP address is placed on the port-channel logical interface.
C: The IP address is placed on the lowest numbered member port.
D: The IP address is assigned via DHCP only.
Answer: B
Which option is?valid for EtherChannel load balancing?
A: source MAC address and source IP address
B: destination MAC address and destination IP address
C: source MAC address and destination IP address
D: source MAC address and destination MAC address
Answer: D
What is the maximum number of switches that can be stacked using Cisco StackWise?
A. 4
B. 5
C. 8
D. 9
E. 10
F. 13
Answer: D
A network engineer wants to add a new switch to an existing switch stack.
Which configuration must be added to the new switch before it can be added to the switch stack?
A. No configuration must be added.
B. stack ID
C. IP address
D. VLAN information
E. VTP information
Answer: A
What percentage of bandwidth is reduced when a stack cable is broken?
A. 0
B. 25
C. 50
D. 75
E. 100
Answer: C
After an EtherChannel is configured between two Cisco switches, interface port channel 1 is in the down/ down state. Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable.
Why is the EtherChannel bundle not working?
A. The switches are using mismatched EtherChannel negotiation modes.
B. The switch ports are not configured in trunking mode.
C. LACP priority must be configured on both switches.
D. The channel group identifier must be different for Switch A and Switch B.
Answer: A
An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server.
What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?
A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.
B. Adjust the EtherChannel load-balancing method based on destination IP addresses.
C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.
D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.
E. Adjust the EtherChannel load-balancing method based on source IP addresses.
Answer: E
Interface FastEthernet0/1 is configured as a trunk interface that allows all VLANs. This command is configured globally: monitor session 2 filter vlan 1 - 8, 39, 52
What is the result of the implemented command?
A. All VLAN traffic is sent to the SPAN destination interface.
B. Traffic from VLAN 4 is not sent to the SPAN destination interface.
C. Filtering a trunked SPAN port effectively disables SPAN operations for all VLANs.
D. The trunk's native VLAN must be changed to something other than VLAN 1.
E. Traffic from VLANs 1 to 8, 39, and 52 is replicated to the SPAN destination port.
Answer: E
A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery Protocol, but it has several routing neighbor relationships.
What would cause the output to show only the single neighbor?
A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.
Answer: A
After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible.
Which vendor-neutral protocol could be used to resolve this issue?
A. Local Area Mobility
B. Link Layer Discovery Protocol
C. NetFlow
D. Directed Response Protocol
Answer: B
Several new switches have been added to the existing network as VTP clients. All of the new switches have been configured with the same VTP domain, password, and version.
However, VLANs are not passing from the VTP server (existing network) to the VTP clients.
What must be done to fix this?
A. Remove the VTP domain name from all switches with "null" and then replace it with the new domain name.
B. Configure a different native VLAN on all new switches that are configured as VTP clients.
C. Provision one of the new switches to be the VTP server and duplicate information from the existing network.
D. Ensure that all switch interconnects are configured as trunks to allow VTP information to be transferred.
Answer: D
After implementing VTP, the extended VLANs are not being propagated to other VTP switches.
What should be configured for extended VLANs?
A. VTP does not support extended VLANs and should be manually added to all switches.
B. Enable VTP version 3, which supports extended VLAN propagation.
C. VTP authentication is required when using extended VLANs because of their ability to cause network instability.
D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to different IOS versions when extended VLANs are in use.
Answer: B
After the recent upgrade of the switching infrastructure, the network engineer notices that the port roles that were once "blocking" are now defined as "alternate" and "backup."
What is the reason for this change?
A. The new switches are using RSTP instead of legacy IEEE 802.1D STP.
B. IEEE 802.1D STP and PortFast have been configured by default on all newly implemented Cisco Catalyst switches.
C. The administrator has defined the switch as the root in the STP domain.
D. The port roles have been adjusted based on the interface bandwidth and timers of the new Cisco Catalyst switches.
Answer: A
没有评论:
发表评论